460x600 SHL-LR-F

PEG460600
 
Semiautomatic machine with hydraulic manipulation.
The machine is designed for cutting of material in vertical and angle cuts, angle cuts are possible to set fluently rom 45° left to 60° right.
It is suitable for serial production and thanks to its robust construction enables to cut wide range of materials including stainless stells and tool steels both profiles and full materials. 
 
Control systém:
The Controler with PLC MITSUBISHI and features an automatic feed control BRP.
Control panel MITSUBISHI as standard equipment. It uses touch display and PLC, which enable semi-automatic cutting (basic setting encluded) as well as communication with operator. 
"Controler show lot of information about cutting proces on the display: 
- Cutting cycle indication,
- indication BRP, 
- indication – blade tightening,
- time of the cut, 
- loading of blade in amperes, 
- speed of the blade, 
- cutting times measuring,  
- list of error messages."
"User´s setting:
- autostop of hydraulic unit
- mode of arm moving after end of the cut
- mode fadt moving of the arm
- mode time lag of shift speed
- mode  blade moving
- mode jaw moving after cutting cycle finish
- diagnostic of inputs and outputs"
STOP function – cutting : it enables to stop cutting by pressing STOP button at any time. The Frame goes up with the running blade without opening the vice.
Regulation of shaft speed (moving to cut) is manual and uses throttle valve placed beside control panel. Automatic (safety) regulation of shift speed PEGAS BRP. Principle: Machine will stop after exceeding set loading (defined in ampers).
Externally situated controlling panel - its position does not depend on the position of turntable position during angular cutting. There is equipped with a safety button, which stops the saw. There is also a feed regulator and buttons  which control the various available movements.
 
Construction:
  • The machine is  constructionaly  designed in that way, so that it corresponds to extreme  exertions in productive conditions.
  • The arm of the machine is robust, heavy weldment and it is designed so that a toughtness and a precision of cut was ensured. 
  • The arm is rotated by a shaft (joint), which is supported by adjustable conical bearings.
  • Drive pulley and tighten pulley are both metal castings. 
  • Working positions of the arm are controlled by the cam and microswitches of the upper and down position of the arm. In the end position microswitch is on, arm goes to selected upper position.
  • The vice is welded. The jaw is made from cast iron. Jaw ensures the safe clamping of the material. 
  • The hydraulically operating vice with long travel is placed in an adjustable dovetail groove. 
  • Moving jaw of the vice is handled by long stroke hydraulic cylinder.  
  • Basic part of the vice moves according to the direction of the angle cut setting, fixation is made by the handle.
  • Turn table is cust iron. Turn table situated on cone roller bearings. 
  • Manuall turning of the table for angle cuts, the position of the turntable is fixed by the lever with the excenter. The position of the turntable for  vertical cutting is arested automatically by the spring mechanism.
  • The angles indicated on the digital display on the control panel MITSUBISHI. Reading of angle by incremental sensor and magnetic tape.
  • Basic equipment of machine: 
  • The blade leading in guides with hardmetal plates and leading bearings and along cast iron pulleys.   
  • There is a guide situated on the firm beam on the drive side. On the tightening side there is the guide situated on the moving beam. 
  • The guide beams of moving band guide is adjustable in whole working range. Manual adjustment and fixing of the guide beams.
  • Guide holder moves in adjustabled dovetail groof.
  • The saw-band is equipped with a guard, which protects the operator from millings and cutting emulsion.   
  • Mechanic tightening of the blade.
  • Automatic indication of blade tension.
  • A passive driven cleaning brush for perfect cleaning and function of blade.
  • Drive of machine is solved by worm gear box with maintenanceless oil filling. Three-phases electromotor  with double winding, with  a frequency converter  for a fluent regulation of the blade speed from 20 to 100 m/min. Sturdy flange with shaft. Termoprotection of engine.
  • The cooling system for emulsion, leaded to the guides of the blade and by LocLine system directly to the cut groove.
  • Massive  base with a tank for chips. Base is designed for manipulation manipulation with machine by pallet truck and also by any hight lift truck.
  • Indication of  blade tightening and opening of the cover.
  • Controlling 24 V.
  • Maschine is equipped with hydraulic system which controles all functions of that maschine. It pushes the arm to cut, pulls up the arm and opens and closes vices.
 
Basic equipment of machine: 
  • Band saw blade.
  • Set of spanners for common service.
  • Manual instructions in eletronic form (CD).
 
Operating cycle: 
After manual adjustment of the jaws the operator starts the cycle with a switch on the control panel. The hydraulic cylinder of the vice grips the material and the saw starts working. The cutting speed of the arm is controlled by a throttle valve. Arm and vice movements after cut finish following set user parameter. The vice opens and the operator can handle the material.
 
 
Juhul kui on küsimusi meie tootevaliku kohta,
helista tööpäeviti 8-17 telefonil 677 5671 või 672 0266